Tus neeg siv phau ntawv rau cov qauv 650E, 1000E, thiab 1250E

Qauv                                                   SERIAL NO.                                          DATE

Kev sib txuas hauv av

Ntsuas kev tiv thaiv los ntawm mains ntsaws lub ntiaj teb tus pin rau hlau nplaum lub cev .... ohm

ELECTRICAL ISOLATION

Megger los ntawm coil mus rau hlau nplaum lub cev

MIN/MAX SUPPLY VOLTAGE TESTS

Ntawm 260v: Pre-clamp.... puv-clamp.... tso tawm

Ntawm 200v: Pre-clamp.... tso tawm

Pre-clamp....Ntawm-clamp....tso tawm

INTERLOCK SEQUENCE

Nrog lub hwj chim qhib, rub HANDLE, tom qab ntawd nias lub pob pib.

Xyuas tias lub tshuab tsis qhib

TU-ON/OFF ANGLES

Kev txav ntawm Bending Beam kom qhib tag nrho-clamping,

ntsuas nyob rau hauv qab ntawm beam dabtsi yog khoov.(4mm txog 6mm) mm

Rov qab txav mus rau lub tshuab hloov-tawm.Ntsuas rov qab

los ntawm 90 °.(Yuav tsum nyob hauv thaj tsam li 15 ° + 5 °) deg

LUB SIJ HAWM

Kev nyeem ntawv ntawm ntug qhov taw qhia thaum khoov beam raug teeb tsa

mus rau 90 ° nrog tus engineer's square.(min 89°, max 91°) deg

MAGNET COJ

Ncaj ntawm sab saum toj nto, nrog rau pem hauv ntej ncej

(max sib txawv = 0.5 mm)Imm

Flatness ntawm saum npoo, hla tus ncej

(max sib txawv = 0.1 mm) mm

BENDING BEAM

Ncaj ntawm qhov chaw ua haujlwm (max sib txawv = 0.25 hli)

Alignment ntawm extension bar (max sib txawv = 0.25 mm)[Nco tseg:Ntsuas qhov ncaj nrog precision ncaj-ntug.]

MAIN CLAMPBAR

Ncaj ntawm dabtsi yog khoov-ntug (max sib txawv = 0.25 hli) Qhov siab ntawm nqa (nrog nqa cov khoom hauv grooves) (min 3 hli) tuaj yeem nqa cov npas tuaj yeem compressed flush nrog nto nrog adjusters teem ntawmⁿ1ⁿthiab khoov beam ntawm 90 °

yog qhov khoov-ntugthaum uas tig musrau, thiabkuv mmlos ntawm, lub nqaj nrog lub nqaj nqaj ntawm 90 °, tuaj yeem hloov kho rau pem hauv ntejkovthiab rov qab los ntawm2 hli

HINGES

Tshawb xyuas lub lubrication ntawm cov ncej.thiab sector blocks

Xyuas kom cov hinges tig ntawm 180 ° dawb thiab du

Kuaj pob khawmtus pindo tsis yogtig.thiab yog loctited

Puas yog cov ntsia hlau tuav tuav tau xauv?

BENDING TEST

(Qhov kev qhia tshwj xeeb tshaj plaws khoov mus rau 90 °, ntawm qhov khoom siv tsawg kawg nkaus.)

Steel xeem daim thickness

Dav ntawm daim di ncauj

mm, Khoov ntev

mm, Khoov radius

Uniformity ntawm khoov lub kaum sab xis (siab tshaj qhov sib txawv = 2 °)

LABELS

Xyuas kom meej meej, adhesion rau lub tshuab thiab kev sib raug zoo.

Daim ntawv teev npe & Serial No

Hluav taws xob ceeb toom

Clampbar ceeb toom

Hloov daim ntawv lo

Kev ruaj ntseg daim kab xev rau pem hauv ntej ob txhais ceg 

TUAG

Tshawb xyuas kev huv, kev ywj pheej los ntawm xeb, blemishes thiab lwm yam

SIJ HAWM

Assembled & Tested.

QA Inspection

Kev ua haujlwm yooj yim

CEEB TOOM

Jdc khoov daim ntawv hlau nplaum tuaj yeem ua rau tag nrho cov clamping quab yuam ntawm ob peb tonnes (saib SPECIFICATIONS).Nws tau nruab nrog ob txhais tes sib cuam tshuam los pab xyuas kom cov ntiv tes tsis tuaj yeem raug ntes tsis tau nyob hauv qab clampbar thaum siv electro-magnetic clamping.

Txawm li cas los xij,Nws yog ib qho tseem ceeb tshaj plaws uas tsuas yog ib tus neeg ua haujlwm siv lub tshuab ib zaug.Nws yog qhov txaus ntshai rau ib tus neeg los ntxig cov khoom ua haujlwm thiab tuav cov clampbars thaum lwm tus neeg ua haujlwm cov keyboards!

NORMAL BENDING

Xyuas kom lub zog yog ON ntawm lub qhov hluav taws xob lub qhov hluav taws xob thiab lub qhov ntev-ntev clampbar yog posi tioned ntawm lub tshuab nrog nws cov khoom nqa nqa nyob rau hauv qhov chaw nrhiav grooves ntawm txhua qhov kawg.

1. Kho rau workpiece thicknesslos ntawm rotating eccentric adjusters ntawm ei kawg ntawm lub clampbar.Nqa cov nqaj hlau mus txog 90 ° txoj hauj lwm thiab xyuas tias nws yog tib yam rau ntawm ntug ntawm lub clampbar - yog tias tsim nyog rov kho cov eccentric lifters.
(Rau qhov ua tau zoo tshaj qhov sib txawv ntawm lub clampbar ntug thiab saum npoo ntawm cov nqaj hlau yuav tsum tau teem rau me ntsis ntau dua li cov hlau tuab yuav tsum tau khoov.)

2.Ntxig lub workpiecetom qab ntawd qaij rau pem hauv ntej ntug ntawm lub clampbar cia thiab ua kom cov kab khoov rau ntawm ntug khoov.
3.Nias thiab tuav lub pob pib.Qhov no siv pre-clamping.

4.Nrog rau lwm txhais tes rub ntawm tus kov.Tag nrho clamping yog tam sim no nws pib matically thov thiab lub khawm START tam sim no yuav tsum tau tso tawm.Con tinue dabtsi yog khoov kom txog thaum lub kaum sab xis xav tau.
5.Lub beam dabtsi yog khoov tuaj yeem thim rov qab li ntawm 10 ° txog 15 ° kom tshem tawm lub workpiece los xyuas qhov khoov lub kaum sab xis.Rov qab los ntawm ntau tshaj 15 ° cia li tig lub tshuab tawm thiab tso tawm cov khoom ua haujlwm.
CEEB TOOM

• Txhawm rau kom tsis txhob muaj kev pheej hmoo ntawm kev puas tsuaj ntawm ntug ntawm lub clampbar lossis denting saum npoo ntawm lub cev hlau nplaum,tsis txhob muab cov khoom me me tso rau hauv lub clampbar.Qhov pom zoo qhov tsawg kawg nkaus khoov ntev siv tus qauv clampbar yog 15 hli, tshwj tsis yog thaum cov khoom ua haujlwm yog nyias lossis mos.
• Lub zog clamping ntawm cov hlau nplaum yog tsawg dua thaum nws kub.Yog li ntawd kom tau txais kev ua tau zoo tshaj plawsthov clamping kom tsis pub ntev tshaj qhov tsim nyogua qhov khoov.

POWER SHEAR(Optional accessory)

Cov lus qhia rau kev siv

Lub hwj chim shear (raws li Makita Model JS 1660) muab ib txoj hauv kev rau kev txiav cov ntawv hlau hauv txoj kev uas tsis tshua muaj kev cuam tshuam nyob rau hauv workpiece.Qhov no yog qhov ua tau vim tias cov shear tshem tawm cov khib nyiab, txog 4 mm dav, thiab feem ntau ntawm cov distortion inherent hauv shearing sheetmetal mus rau hauv cov khib nyiab no.Rau kev siv nrog Jdcbend lub shear tau haum nrog cov lus qhia tshwj xeeb sib nqus.

Lub shear ua haujlwm zoo ua ke nrog Jdcbend Sheetmetal Folder;Jdcbend muab ob qho tib si txhais tau tias tuav lub workpiece tsau thaum raug txiav thiab tseem yog ib txoj hauv kev rau kev taw qhia cov cuab yeej kom txiav ncaj ncaj yog ua tau.Txiav ntawm txhua qhov ntev tuaj yeem ua rau cov hlau txog li 1.6 hli tuab lossis txhuas txog li 2 hli tuab.

Txhawm rau siv lub cuab yeej ua ntej tso cov ntawv hlau ua haujlwm hauv qab lub clampbar ntawm Jdcbend thiab tso nws kom cov kab txiav yog raws nraim.] hlipem hauv ntej ntawm ntug ntawm Bending Beam.

Lub toggle hloov sau tias "NORMAL / AUX CLAMP,, yuav pom nyob ib sab ntawm lub ntsiab ON / OFF hloov. Hloov qhov no mus rau AUX CLAMP txoj hauj lwm tuav lub workpiece kom ruaj khov nyob rau hauv txoj hauj lwm.

Tso lub shear rau ntawm sab xis kawg ntawm Jdcbend thiab xyuas kom meej tias daim ntawv qhia sib nqus txuas nrog rau sab pem hauv ntej ntawm Bending Beam.Pib lub hwj chim shear thiab ces thawb nws tusyees mus txog thaum txiav tiav.

Nco tseg:

1. Rau kev ua tau zoo tshaj plaws, cov hniav tshem tawm yuav tsum tau kho kom haum rau cov thickness ntawm cov khoom yuav raug txiav.Thov nyeem cov lus qhia Makita muab nrog JS1660 shear.
2. Yog hais tias lub Shear tsis txiav dawb xyuas tias cov hniav yog ntse.

NPLOG LIAB

FOLDING A LIP (HEM)

Cov txheej txheem siv rau daim di ncauj yog nyob ntawm qhov workpiece thickness thiab rau qee qhov, ntawm nws qhov ntev thiab dav.

Thin Workpieces (txog 0.8 hli)

1.Ua raws li ib txwm khoov tab sis txuas ntxiv khoov kom deb li deb tau (135 °).
2. Tshem tawm lub clampbar thiab tawm ntawm lub tshuab ua haujlwm tab sis txav nws rov qab txog 10 hli.Tam sim no viav vias lub beam dabtsi yog khoov rau compress daim di ncauj.(Tsis tas yuav tsum tau clamping).[Faj seeb: Tsis txhob sim ua daim di ncauj nqaim ntawm tuab workpieces].

3.Nrog nyias workpieces, thiab / los yog qhov twg daim di ncauj tsis yog nqaim heev, ib tug ntau complete flattening yuav ua tau tiav los ntawm cov nram qab no nrog sib nqus clamping nkaus xwb:

ROLLED EDGE

FORMING ROLLED EDGE

Rolled npoo yog tsim los ntawm wrapping lub workpiece nyob ib ncig ntawm ib puag ncig steel bar los yog ib daim ntawm tuab-walled yeeb nkab.

1.Position lub workpiece, clampbar thiab dov bar raws li qhia.
a) xyuas kom meej tias lub clampbar tsis sib tshooj pem hauv ntej ncej ntawm ma chine ntawm "a" vim qhov no yuav tso cai rau cov hlau nplaum sib nqus los hla lub dov bar thiab yog li clamping yuav tsis muaj zog heev.

b) Xyuas kom tseeb tias lub dov bar yog so ntawm lub steel pem hauv ntej ncej ntawm lub ma chine ("b") thiab tsis ntxiv rov qab rau ntawm txhuas ib feem ntawm qhov chaw.

c) Lub hom phiaj ntawm clanipbar yog muab txoj hauv kev sib nqus ("c") mus rau hauv qhov dov bar.

2. qhwv lub workpiece kom deb li deb tau ces rov ua txoj hauj lwm raws li qhia.

 

3. Rov ua kauj ruam 2 raws li xav tau.

TEST PIB

Cov lus qhia rau kev tsim daim ntawv xeem

Txhawm rau kom paub txog koj lub tshuab thiab hom kev ua haujlwm uas tuaj yeem ua tau nrog nws, nws raug nquahu kom ua ib qho kev xeem-thooj raws li tau piav qhia hauv qab no:

1.Xaiv ib daim ntawm 0.8 hli tuab me me hlau los yog txhuas ntawv thiab txiav rau 335 x 200 hli.
2.Kim kab ntawm daim ntawv raws li qhia hauv qab no:

3.Txhim khoKhoov 1thiab tsim ib daim di ncauj rau ntawm ntug ntawm lub workpiece.(Saib

“Folded LIP”)

4.Tig lub xeem daim thiab xaub nws nyob rau hauv lub clampbar, tawm hauv folded ntug ntawm koj.Tilt lub clampbar rau pem hauv ntej thiab kabKhoov 2.Ua qhov no khoov rau 90 °.Tam sim no daim ntawv xeem yuav tsum zoo li no:

…TEST PIB

5.Tig daim ntawv xeem thiab uaKauj Ruam 3, Kauj Ruam 4thiabKhoov 5txhua qhov rau 90 °
6.Ua kom tiav cov duab, cov khoom seem yuav tsum tau dov ib ncig ntawm 25 mm inch round bar ntawm steel.

• Xaiv lub 280 mm clamp-bar thiab muab tso rau, qhov ntsuas thiab lub voj voog ntawm lub tshuab raws li qhia hauv qab "ROLLED EDGE" ua ntej hauv phau ntawv no.
• Tuav lub round bar nyob rau hauv txoj hauj lwm nrog sab tes xis thiab siv pre clamping los ntawm nias thiab tuav lub khawm START nrog sab laug tes.Tam sim no siv koj sab tes xis rub tus kov zoo li ua ib qho kev khoov zoo tib yam (lub khawm START yuav raug tso tawm).qhwv lub workpiece kom deb li deb tau (kwv yees li 90 °).Reposition lub workpiece (raws li qhia nyob rau hauv "Forming a Rolled Edge") thiab qhwv dua.Txuas ntxiv kom txog thaum lub yob kaw.

Tam sim no daim ntawv xeem tau tiav lawm.

BOXES...

UA HAUJ LWM (Siv luv CLAMPBARS)

Muaj ntau txoj hauv kev tso tawm lub thawv thiab ntau txoj hauv kev ntawm folding lawv.JDCBEND yog qhov zoo tshaj plaws rau kev tsim cov thawv, tshwj xeeb tshaj yog cov uas nyuaj, vim tias siv cov clampbars luv luv los tsim cov folds kuj unhindered los ntawm yav dhau los folds.

Plain Boxes

1.Ua thawj ob khoov siv lub clampbar ntev raws li kev khoov ib txwm.
2.Xaiv ib los yog ntau tshaj ntawm cov luv clampbars thiab txoj hauj lwm raws li qhia.(Nws tsis yog yuav tsum tau ua kom ntev npaum li qhov khoov yuav nqa dhau qhov khoob ntawm yam tsawg kawg nkaus20 mmnruab nrab ntawm cov clampbars.)

Rau khoov mus txog 70 mm ntev, tsuas yog xaiv qhov loj tshaj plaws clamp daim uas yuav haum.Rau ntev ntev nws yuav tsum tau siv ob peb daim clamps.Tsuas yog xaiv qhov ntev tshaj plaws clampbar uas yuav haum rau hauv, tom qab ntawd qhov ntev tshaj plaws uas yuav haum rau qhov sib txawv ntawm qhov seem, thiab tej zaum yuav yog qhov thib peb, yog li ua qhov ntev yuav tsum tau ua.

Rau repetitive dabtsi yog khoov cov clamp pieces yuav tsum tau ntsaws ua ke los ua ib tug tib chav tsev nrog rau qhov ntev yuav tsum tau.Xwb, yog hais tias lub thawv muaj ntiav sab thiab koj muaj muajslotted clampbar,tom qab ntawd nws yuav nrawm dua los ua cov thawv rau tib yam li cov tais ntiav.(Saib tshooj tom ntej: TRAYS)

Lipped thawv

Lipped thawv tuaj yeem ua tau siv cov txheej txheem ntawm luv clampbars muab ib qho ntawm qhov ntev yog ntau dua qhov dav ntawm clampbar (98 mm).

1.Siv tag nrho-ntev clampbar, tsim qhov ntev wise folds 1, 2, 3, & 4.
2.Xaiv lub clampbar luv luv (los yog tej zaum ob lossis peb txuas ua ke) nrog qhov ntev tsawg kawg ntawm daim di ncauj-dav luv luv dua li qhov dav ntawm lub thawv (kom nws yuav raug tshem tawm tom qab).Daim ntawv folds 5, 6, 7 & 8. Thaum tsim cov folds 6 & 7, yuav tsum ceev faj coj lub ces kaum

tabs sab hauv lossis sab nraud ntawm lub thawv, raws li xav tau.

...BOXES...

Cov thawv nrog nyias qhov xaus

Ib lub thawv ua nrog nyias qhov xaus muaj ntau qhov zoo:

-nws txuag cov khoom yog tias lub thawv muaj sab sib sib zog nqus,

- nws tsis tas yuav tsum tau kaum notching,

-Txhua qhov kev txiav tawm tuaj yeem ua tiav nrog guillotine,

-Txhua qhov folding tuaj yeem ua tiav nrog lub tiaj puv-ntev clampbar;

thiab ib co drawbacks:

- ntau folds yuav tsum tau tsim,

-ntau cov ces kaum yuav tsum tau koom nrog, thiab

-ntau hlau npoo thiab fasteners qhia ntawm lub thawv tiav.

Ua lub thawv zoo li no yog ncaj nraim rau pem hauv ntej thiab qhov ntev-ntev clampbar tuaj yeem siv rau txhua qhov quav.

1. Npaj cov blanks raws li qhia hauv qab no.
2.First tsim plaub folds nyob rau hauv lub ntsiab workpiece.

3.Tom ntej no, ua 4 flanges ntawm txhua qhov kawg.Rau txhua qhov ntawm cov quav no, ntxig qhov nqaim flange ntawm qhov kawg hauv qab lub clampbar.
4. Koom lub thawv ua ke.

 

Flanged thawv nrog cov ces kaum

Plain cornered thawv nrog sab nraud flanges yog ib qho yooj yim los ua yog tias qhov ntev thiab qhov dav yog ntau dua li qhov dav ntawm clampbar ntawm 98 mm.Kev tsim cov thawv nrog cov flanges sab nraud muaj feem xyuam rau kev ua TOP-HAT SECTIONS ( piav qhia hauv ntu tom qab - saib Cov Ntsiab Lus ).

4. Npaj qhov khoob.
5.Siv tag nrho-ntev clampbar, daim ntawv folds 1, 2, 3 & 4.
6.Insert lub flange nyob rau hauv lub clampbar rau daim ntawv quav 5, thiab ces quav 6.
7.Siv cov clampbars luv luv, ua kom tiav folds 7 & 8.

...BOXES

Flanged Box nrog Corner Tabs

Thaum ua ib lub thawv flanged sab nraud nrog kaum tabs thiab tsis siv cov khoom sib cais, nws yog ib qho tseem ceeb los tsim cov folds nyob rau hauv raws li qhov tseeb.

1. Npaj qhov khoob nrog kaum tabs teem raws li qhia.

2.Ntawm ib kawg ntawm qhov ntev-ntev clamp bar, tsim tag nrho cov tab folds "A" rau 90. Nws yog qhov zoo tshaj los ua qhov no los ntawm kev ntxig lub tab hauv qab lub clampbar.
3.Thaum tib kawg ntawm qhov ntev-ntev clampbar, daim ntawv foldsⁿBⁿ rau 45° xwb.Ua qhov no los ntawm kev ntxig rau sab ntawm lub thawv, tsis yog hauv qab ntawm lub thawv, hauv qab lub clampbar.
4. Ntawm qhov kawg ntawm qhov ntev-ntev clampbar, tsim cov flange folds "C" rau 90 °.
5.Siv cov clampbars luv luv, ua tiav foldsⁿBⁿrau 90.
6. Koom nrog cov ces kaum.
Nco ntsoov tias rau cov thawv sib sib zog nqus nws yuav zoo dua los ua lub thawv nrog cov khoom sib cais.

SLOTTED CLAMPBAR

FORMING TRAYS (SIV SLOTTED CLAMPBAR)

Lub Slotted Clampbar, thaum muab khoom, yog qhov zoo tagnrho rau kev ua cov tais ntiav thiab cov lauj kaub sai thiab raug.Qhov zoo ntawm cov slotted clampbar tshaj cov txheej ntawm luv clampbars rau kev ua cov tais yog tias cov ntug bending yog automati cally raws li tus so ntawm lub tshuab, thiab lub clampbar txiav lifts los pab txhawb kev ntxig lossis tshem tawm ntawm lub workpiece.Tsis yog-tus-tsawg, cov clampbars luv luv tuaj yeem siv los ua cov tais ntawm qhov tsis txwv qhov tob, thiab tau kawg, yog qhov zoo dua rau kev ua cov duab nyuaj.

Nyob rau hauv kev siv, cov slots yog sib npaug rau qhov khoob ntawm cov ntiv tes ntawm lub conven tional box & pan folding tshuab.Qhov dav ntawm cov slots yog xws li tias ob lub qhov yuav haum cov tais hla qhov loj ntawm 10 mm, thiab tus naj npawb thiab qhov chaw ntawm cov slots yog li ntawd.rau txhua qhov ntau thiab tsawg ntawm lub tais, muaj peev xwm nrhiav tau ob lub qhov uas yuav haum nws.(Qhov luv tshaj plaws thiab ntev tshaj plaws lub tais loj qhov slotted clampbar yuav haum yog teev nyob rau hauv SPECIFICATIONS.)

Yuav kom fold li ib lub tais ntiav:

1. Fold-up thawj ob sab sab nraud thiab lub kaum sab xis siv lub slotted clampbar tab sis tsis quav ntsej txog qhov muaj ntawm cov qhov.Cov slots no yuav tsis muaj qhov cuam tshuam pom ntawm qhov ua tiav folds.
2. Tam sim no xaiv ob lub qhov ntawm qhov uas yuav fold-up qhov seem ob sab.Qhov no ua tau yooj yim heev thiab ceeb sai sai.Tsuas yog kab-up sab laug ntawm ib feem ua tais nrog rau sab laug tshaj qhov thiab saib seb puas muaj ib lub qhov rau sab xis thawb rau hauv;yog tias tsis yog, xaub lub tais mus txog rau sab laug yog ntawm qhov txuas ntxiv thiab sim dua.Feem ntau, nws yuav siv li 4 qhov kev sim nrhiav ob qhov chaw tsim nyog.
3. Thaum kawg, nrog ntug ntawm lub tais hauv qab lub clampbar thiab nruab nrab ntawm ob qhov chaw xaiv, quav rau sab seem.Cov sab tsim yav dhau los mus rau hauv cov qhov chaw xaiv raws li qhov kawg folds tiav.

Nrog lub tais ntev uas yuav luag ntev npaum li lub clampbar nws yuav tsum tau siv ib kawg ntawm lub clampbar lieu ntawm lub qhov.

PUAS YOG

SIV LUB ROOJ

Cov backstops muaj txiaj ntsig zoo thaum muaj ntau qhov khoov yuav tsum tau ua kom tag nrho cov uas yog tib qhov deb ntawm ntug ntawm lub workpiece.Thaum lub backstops raug teeb tsa muaj pes tsawg tus khoov tuaj yeem ua yam tsis tas yuav tsum tau ntsuas lossis kos tawm ntawm lub workpiece.

Feem ntau cov backstops yuav raug siv nrog ib lub bar nteg tawm tsam lawv thiaj li tsim ib tug ntev nto ntawm qhov uas yuav siv lub ntug ntawm workpiece.Tsis muaj spe cial bar yog muab tab sis qhov txuas ntxiv los ntawm cov nqaj nqaj tuaj yeem siv tau yog tias tsis muaj lwm qhov haum.

CEEB TOOM:Yog hais tias yuav tsum tau teem lub backstophauv qablub clampbar, ces qhov no yuav ua tau los ntawm kev siv ib tug sawb ntawm sheetmetal tib thickness li lub workpiece, nrog rau cov backstops.

YOG

Kuaj xyuas qhov tseeb ntawm koj lub tshuab

Txhua qhov chaw ua haujlwm ntawm Jdcbend yog tsim los kom ncaj thiab tiaj tus mus rau hauv 0.2 hli dhau ntawm tag nrho qhov ntev ntawm lub tshuab.

Qhov tseem ceeb tshaj plaws yog:

1. qhov ncaj ntawm qhov chaw ua hauj lwm ntawm lub nqaj nqaj,
2. qhov ncaj ntawm qhov khoov ntug ntawm lub clamp bar, thiab
3. parallelism ntawm ob qhov chaw.

Cov chaw no tuaj yeem kuaj xyuas nrog qhov tseeb ncaj-ntug tab sis lwm txoj hauv kev zoo ntawm kev kuaj xyuas yog siv cov chaw rau ib leeg.Ua li no:

1. Hlav lub nqaj hlau mus txog 90 ° txoj hauj lwm thiab tuav nws nyob ntawd.(Lub nqaj tuaj yeem raug kaw hauv txoj haujlwm no los ntawm kev tso lub nraub qaum-nres clamp dab tshos qab lub kaum sab xis ntawm tus kov).
2. Saib xyuas qhov sib txawv ntawm qhov khoov ntug ntawm lub clamp bar thiab qhov chaw ua hauj lwm ntawm qhov khoov beam.Siv cov clamp bar adjusters teeb qhov sib txawv no mus rau 1 hli ntawm txhua qhov kawg (siv cov seem ntawm cov ntawv hlau, lossis lub ntsuas qhov ntsuas).

Xyuas kom meej tias qhov sib txawv yog tib yam li ntawm lub clampbar.Txhua qhov kev hloov pauv yuav tsum tsis pub dhau ± 0.2 hli.Tliat yog qhov sib txawv yuav tsum tsis txhob ntau tshaj 1.2 hli thiab yuav tsum tsis pub tsawg tshaj 0.8 hli.(Yog tias cov neeg kho tsis tau nyeem ib yam ntawm txhua qhov kawg, rov pib dua lawv raws li tau sau tseg hauv MAINTENANCE).

Nco tseg:

1. Qhov ncaj ntawm lub clampbar raws li pom nyob rau hauv qhov siab (los ntawm pem hauv ntej) tsis yog ib qho tseem ceeb vim qhov no tau flattened tawm los ntawm hlau nplaum clamping sai li sai tau thaum lub tshuab qhib.
2. Qhov sib txawv ntawm cov nqaj hlau thiab cov hlau nplaum lub cev (raws li tau pom nyob rau hauv txoj kev npaj-saib nrog cov nqaj nkhaus hauv nws txoj haujlwm hauv tsev) feem ntau yog li 2 mus rau 3 hli.Qhov kev sib txawv no yogtsis yogib qho kev ua haujlwm ntawm lub tshuab thiab tsis cuam tshuam rau kev khoov qhov tseeb.
3. Lub Jdcbend tuaj yeem tsim cov folds ntse hauv cov ntsuas nyias thiab hauv cov ntaub ntawv tsis muaj ferrous xws li txhuas thiab tooj liab.Txawm li cas los xij nyob rau hauv cov ntaub ntawv tuab ntawm cov hlau thiab stainless hlau tsis xav kom ua tiav qhov ntse ntse (saib cov lus qhia).
4. Kev sib txawv ntawm qhov khoov hauv cov ntsuas tuab tuaj yeem txhim kho los ntawm kev siv cov khoom seem ntawm cov khoom ua haujlwm los sau rau hauv cov khoom tsis siv nyob rau hauv lub clampbar.

MAINTENANCE

UA NTEJ

Yog hais tias qhov chaw ua hauj lwm liab qab ntawm lub tshuab ua xeb, tarnished los yog dam hnub nyoog, lawv tuaj yeem hloov kho tau yooj yim.Txhua qhov tsaj burrs yuav tsum tau muab tshem tawm, thiab qhov chaw rubbed nrog P200 emery ntawv.Thaum kawg siv cov tshuaj tsuag- ntawm cov xeb xws li CRC 5.56 lossis RP7.

HINGE LUBRICATION

Yog tias Jdcbend sheetmetal folder siv tas li, ces roj lossis roj lub pob khawm ib hlis ib zaug.Yog tias lub tshuab siv tsawg dua, ces nws yuav raug lubricated tsawg dua.

Lubrication qhov yog muab nyob rau hauv ob lugs ntawm lub ntsiab pob khawm phaj, thiab spherical bearing nto ntawm lub sector block yuav tsum muaj lubricant thov rau nws.

ADJUSTERS

Cov adjusters ntawm qhov kawg ntawm lub ntsiab clampbar yog los tswj cov nyiaj pub dawb rau lub thickness ntawm lub workpiece ntawm lub dabtsi yog khoov-ntug thiab khoov beam.Cov adjusters yog Hoobkas-teeb kom muab lub thickness pub ntawm 1 hli thaum lub adjuster ntsuas "1".

1.Tuav lub beam khoov ntawm 90.

2.Insert ib daim me me ntawm 1 hli sheetmetal ntawm txhua qhov kawg ntawm lub npoo dabtsi yog khoov thiab cov nqaj dabtsi yog khoov.
3.Ignoring cov cim qhia, kho cov adjusters kom txog rau thaum lub 1 hli pieces tsuas yog maj mam "nipped" ntawm lub dabtsi yog khoov-ntug thiab khoov beam.
4.Siv tus yuam sij 3 hli Allen, ua tib zoo xoob lub grub-ntsia hlau kom dawb lub nplhaib knurled ntawm ib qho ntawm cov adjusters.Tom qab ntawd tig lub nplhaib kom txog thaum qhov taw qhia ing slit qhia tias "1ⁿ.Ua qhov no yam tsis tau tig lub cev sab hauv ntawm tus ad juster.Tom qab ntawd rov zawm lub grub-ntsia hlau.
5.Reset lwm tus adjuster tib yam.
Lub caij nplooj ntoos hlav-loaded lifting npas nyob rau hauv qab ntawm lub adjusters yuav lo yog av los yog xeb-forming noo noo nkag mus rau hauv. Yog hais tias qhov no tshwm sim, kho nws los ntawm nias lub pob nyob rau hauv thiab tawm nrog ib tug blunt cuab tam thaum txau nyob rau hauv ib tug nkag mus rau hauv lub lubricant xws li CRC. 5.56 rp 7.